Manual lifting is too slow
Large rolls force operators to bend, lift, roll and reposition material repeatedly.
Roll clamp cart for film, paper and cylindrical loads
Film and paper roll clamp loading equipment
Electric roll clamp carts handle PE, PP, PVC, stretch film, packaging film, paper rolls and tape jumbo rolls with clamping, lifting, 360 degree rotation and machine-side loading. Sizing is based on roll diameter, weight, width, lift height, aisle and site photos.
360-800 mm roll diameter
350-500 kg reference load
Slitter feeding
Custom lift height
One operator
500 kg / 3000 mm
counterbalanced high-lift reference
500 kg / 1500 mm
stand-on rotating clamp reference
350 kg / 1500 mm
semi-electric push model reference
If roll handling slows your line, fix these four points first
Buyers usually need less manual lifting, safer control and faster machine-side loading.
Round loads are unstable
Film rolls, paper rolls and drums can roll, slip or drift when supported from the bottom.
Machine loading is hard to align
Slitters, rewinders and packaging machines need the right height, angle and approach.
Too many people are involved
Moving, holding, turning and feeding a roll often ties up two or three workers.
Clamp the outside diameter. Lift to height. Rotate into position.
The practical value is not only the clamp action. Buyers need the roll picked from a pallet or floor, raised to machine height, turned to the right direction and held steady beside the line.
Clamp
Curved clamp arms grip the outside diameter of rigid film rolls, paper rolls and tape jumbo rolls.
Lift
Lift height can be configured around 1500 mm, 3000 mm or another machine-side requirement.
Rotate
360 degree left/right hydraulic rotation helps change vertical or horizontal roll orientation.
Feed
Move rolls into slitters, rewinders, laminating, coating, printing and packaging stations.
Practical product parameters and custom range
These custom roll clamp configurations are not fixed catalogue models. The ranges give buyers a practical starting point before final sizing.
Parameters can be customized by roll weight, diameter, width, lift height, aisle width, floor condition, battery requirement and whether the roll is picked vertically or horizontally. Keep 10-20 cm clearance on both sides of the clamp during operation.
Higher lift / heavy daily use
Counterbalanced electric roll clamp
For production lines that need electric travel, electric lifting and hydraulic clamping with a higher mast.
- Rated load
- 500 kg
- Lift height
- 3000 mm clamp-center height
- Roll diameter
- 300-800 mm
- Rotation
- 360 degrees, left/right
- Battery
- 24V 220Ah lead-acid
- Aisle
- about 1400 mm
- Truck size
- about 1020 mm wide, 1850 mm high; 1600/2100 mm mast optional
- Drive / lift motor
- 1.2 kW / 2.2 kW
- Suitable for rigid film rolls, paper rolls and hard-core roll material
- Counterbalanced layout, no front support legs under the roll
- Wear-resistant rubber pads on clamp plates
Best fit
- High lift point or machine-side loading above standard height
- Frequent daily use with powered travel and lift
- Roll underside must stay clear of front support legs
Avoid when
- Very narrow aisles below the confirmed turning radius
- Soft or easily deformed rolls that cannot tolerate side pressure
Confirm first
- Actual roll weight and hardness
- Clamp-center height and machine inlet height
- Aisle width, turning space and floor condition
Standard film roll loading
Stand-on electric rotating clamp
A compact electric travel model for vertical pickup and repeated machine-side roll feeding.
- Rated load
- 500 kg
- Lift height
- 1500 mm
- Roll diameter
- 360-800 mm
- Roll height
- 1320 mm reference
- Rotation
- 360 degrees, dual hydraulic
- Voltage
- 24V
- Pump power
- 24V / 1600 W
- Aisle
- about 1100 mm
- Reference size
- 1.8 x 0.8 x 1.6 m
- Good fit for slitter, rewinder and packaging line loading
- Electric travel with stand-on operation
- Used when rolls are picked upright and rotated into position
Best fit
- Repeated loading beside slitters, rewinders and packaging lines
- Vertical pickup followed by 360 degree positioning
- Medium travel distance where stand-on driving improves rhythm
Avoid when
- Loads needing more lift height than the 1500 mm reference
- Rolls outside the confirmed clamp diameter range
Confirm first
- Roll diameter, roll height and core strength
- Whether left/right rotation is required
- Clearance around the machine-side loading point
Lower frequency / budget option
Semi-electric manual-push clamp
For short indoor transfers where electric lifting and clamping are needed, but travel can remain manual.
- Rated load
- 350 kg
- Lift height
- 1500 mm
- Roll diameter
- 360-800 mm
- Roll height
- 1600 mm reference
- Rotation
- 360 degrees, dual hydraulic
- Battery
- 12V / 80Ah
- Pump power
- 12V / 1600 W
- Aisle
- about 1100 mm
- Reference size
- 1.3 x 0.95 x 1.9 m
- Light film-roll option
- 250 kg, 1500 mm lift, 600-800 mm roll diameter
- Battery option
- 12V / 80Ah or 12V / 120Ah by duty cycle
- Best for short-distance transfer and fewer daily cycles
- White nylon or polyurethane wheels for epoxy and painted floors
- Lower purchase cost while keeping electric lift and clamp actions
- A lighter 250 kg film-roll version can be considered for low-frequency loading.
Best fit
- Short indoor transfer with low or medium frequency
- Budget-sensitive sites that still need powered lift and clamp rotation
- Smooth floors where manual pushing is acceptable
Avoid when
- Long travel routes or high daily cycle counts
- Steep slopes, rough floors or heavy continuous duty
Confirm first
- Daily handling count and travel distance
- Operator pushing route and turning points
- Battery endurance and wheel material for the floor
Side pick / large diameter
Side-clamp paper roll and cable roll cart
For cloth rolls, paper rolls, cable reels and other cylindrical loads that are handled from the side instead of full 360 degree rotation.
- Reference load
- 500-800 kg
- Applicable diameter
- 200-1300 mm
- Tilt angle
- Left / right 30 degree reference
- Lift / drive
- Electric lift, electric travel option
- Fork / clamp
- Thickened fork frame with side clamp
- Custom confirmation
- Roll hardness, core strength and side clearance
- Useful when the roll cannot be gripped from the bottom or rotated fully
- Suitable for cloth, paper, cable and other large-diameter cylindrical loads
- Parameter range must be checked against roll weight, width and center of gravity
Fit
- Side-pick loading where a roll sits on a pallet or machine cradle
- Large roll diameter beyond ordinary small clamp range
- Paper, cloth or cable reels that require gentle side holding
Avoid
- Thin film rolls that need precise 360 degree machine-side rotation
- Very soft rolls that cannot accept side pressure
Confirm
- Actual roll diameter and width
- Allowed side pressure and core strength
- Need for 30 degree tilt or full 360 degree rotation
Practical film-roll applications
Use the site to show actual workflow: pickup, short transfer, rotation and machine-side loading.
Plastic film slitter loading
Move PE, PP, PVC, stretch film or packaging film rolls from staging to the slitter unwind position.
Paper roll and core handling
Lift paper rolls or hard-core rolls from storage without rolling them across the floor.
Outdoor receiving to workshop
Transfer rolls from receiving, truck side or yard staging into the production area.
Warehouse aisle circulation
Use counterbalanced configurations where racks, pallets and aisle width limit the approach.
Actual product and application photos
Cleaned gallery without unrelated logos or watermarks, focused on film rolls, paper rolls, machine-side loading and warehouse transfer.
Film roll beside slitter line
Roll clamp cart staged at the machine side for plastic film roll loading and line-side feeding.
Outdoor roll transfer
Operator moves a large roll outside the workshop with controlled clamp support instead of manual rolling.
Paper roll storage handling
Large paper rolls are lifted from storage and positioned for the next process with one operator.
Warehouse aisle transfer
Counterbalanced roll clamp configuration for warehouse movement where pallets, racks and aisles limit space.
Compact rotating clamp
Close-up of the rotating clamp structure for smaller workshops and repeated roll pickup.
High-load counterweight type
Counterweight style configuration for heavier rolls, longer lift height and custom clamp dimensions.
Documentation and shipment support
The website should describe document types that can be prepared for real orders. Final files depend on the actual truck, battery, route and carrier requirement.
Battery MSDS/SDS
Lead-acid battery configurations can be supported with safety documents covering valve-regulated, maintenance-free and non-spillable descriptions.
Transport identification
Transport attribute or identification documents can be prepared according to actual model, battery, packaging and route.
Non-dangerous booking support
Non-dangerous booking documents can be prepared according to carrier and destination requirements for material-handling equipment shipments.
Custom confirmation files
Final documents should match load, roll diameter, roll width, lift height, voltage, battery and packaging instead of treating reference ranges as fixed models.
Stop lifting rolls by hand
Share your roll size and loading process. Dubhe will match the roll clamp cart to your actual production line.